& nbsp; First, adjust the formula to control water consumption should not exceed 4.5 parts, can be used with a low-boiling liquid compound to use as an auxiliary hair if necessary replace part of the water-foaming agent. Note that the formula of water, must not exceed 5 parts. Low density foams highest temperature safety point 160 ° C, must not exceed 170 ° C. Div>
& nbsp; & nbsp; & nbsp; Second, strict control of each component of measurement accuracy and reduce measurement error. In a continuous block foam production, should pay attention to adjust the speed of the mixing head and material discharge conveyor speed, so that coordination, to avoid the conveyor speed is too slow or not caused by excessive discharge of material from the hair from the hair has started to flow into undercurrent phenomenon material at the bottom, so that the material can not normally produce hair from collapse, but the collapse of the material is not easy to produce local "gas species", causing local heat accumulation and increases the risk of scorch. In actual production, process parameters such as Tengen poor bubble will appear at the bottom of a block of little yellow coking line. Div>
& nbsp; & nbsp; & nbsp; Third, should avoid a new production of the material foams by external force compression, the reason is because the foam when it is not fully matured, by external compression will affect the foam network, bubble structure, but also to avoid the accumulation of heat generated by compression, adding new bubble risk of spontaneous combustion. In particular, the rise in the foam reaction most sensitive stage, any operational errors and vibration, such as jerking motion conveyor chain tight generated excessive wrinkling of release paper and the belt will cause bumps immature compressed foam, causing scorch. Div>
& nbsp; & nbsp; & nbsp; Fourth, strict attention to aging storage program foams, for flexible polyurethane foam blocks production, ripening new bubble is a high incidence of fire accident. Due to the large foam block internal temperature is high, the heat long duration, usually reaches an internal temperature of maximum time is about 30 ~ 60min, and 3 ~ 4h or longer to begin a slow decline, during this time, new bubbles have left the production line and into the often overlooked curing the reservoir, without good control measures, will easily lead to a fire. Data report, molecular weight 5,000 yuan alcohol, 4.7 parts of water and 8 parts of F-11, TDI index when massive soft foam 1.07 isocyanate production density of 22kg / ㎥, the new foam found a small amount of yellowish after 2h smoke, although the foam surface temperature is not high, but the foam inside is very dangerous in the early stages of decomposition, the temperature at 200 ~ 250 ° C or so, has begun to spontaneous combustion. Div>
& nbsp; & nbsp; & nbsp; Fifth, to prevent foam spontaneous combustion, the new production of foams for aging storage shall not exceed three layers stacked, spacing must be greater than 100mm, the best place alone. Curing the reservoir should be equipped with full-time staff to strengthen monitoring, such as the internal temperature of the foam was measured 15min intervals, monitoring for at least 12h, or even longer, then normal storage. For it is possible to produce high-temperature foam, foam chunks will be cut according to the level of need (such as the thickness of 200mm), to facilitate the foam heat. When they find the foam spontaneous combustion or smoke, you should use water spray or use a fire extinguisher, must not move any foam or open windows and doors, so as to avoid increasing air traffic leaving the spread of fire.
Order 在线留言
Contact us 联系我们
Toll Free: 400-826-8887
Phone: 86-0577-65336533
Fax: 86-577-65336599
Mr. Chen: 13515871991
E-mail: lxpu4008268887@sina.com
QQ: 2088530984
Address: Ruian international automobile and motorcycle industry park Luoshan Road on the 8th
Official Taobao: http: //shop122069384.taobao.com/
Official microblogging: http: //weibo.com/lxpu
Micro-channel public service number: lxpuwx
Phone: 86-0577-65336533
Fax: 86-577-65336599
Mr. Chen: 13515871991
E-mail: lxpu4008268887@sina.com
QQ: 2088530984
Address: Ruian international automobile and motorcycle industry park Luoshan Road on the 8th
Official Taobao: http: //shop122069384.taobao.com/
Official microblogging: http: //weibo.com/lxpu
Micro-channel public service number: lxpuwx
Free hotline:13515871991
COPYRIGHT © 2016 Zhejiang Raytheon Polyurethane Co., Ltd. ALL RIGHTS RESERVED POWER BY HEYI MACHINERY CO., LTD.
Address:Ryan international automobile and motorcycle industry park Luoshan Road on the 8th phone:400-826-8887 Contact: Chen Phone:13515871991
Address:Ryan international automobile and motorcycle industry park Luoshan Road on the 8th phone:400-826-8887 Contact: Chen Phone:13515871991